DM - 150, 160, 180, 186V / VS Series
photo shown DM-160V
*Standard accessories shall be subject to the quotation.
- 1. The body casting is made of high quality Meechanite.
- 2. Spindle is made of SCM-4 shaft chrome-molybdenum steel, heat treatment after carburizing,
and precision ground. - 3. Turcite-B are coated on XY-axes.
- 4. Work table & slide ways of XYZ-axes are hardened & ground.
- 5. Square slideway on Y-axis.
- 6. Direct-shift "High / Low" switch.
- 7. The slideway of Z-axis is hardened & ground for DM-180 & DM-186.
- 8. Square slideway on Z-axis for DM-180 & DM-186.
- 1. Chip tray
- 2. Digital readout
- 3. X-axis power feed, only for DM-160, DM-180
- 4. Y-axis power feed
- 5. XY-axes gear box
- 6. XY-axes servo motor, table feed
- XY axes just can be installed one device of 3~6
- 7. XY-axes ball screw
- 8. Table length 54" (1370mm)
- ◎ 9. Spindle NT-40 (only for Dm-160)
- ◎ 10. Swing arm type of operation panel (only for DM-160)
- ◎ 11. Z-axis gear elevating reducer motor for knee up/down (only for DM-160)
- 1. Auto lubrication system.
- 2. XY-axes with Turcite-B
- 3. Coolant system.
- 4. Darw bar
- 5. Splash shield
- 6. Electric box
- 7. Halogen light
- 8. Tools & Tool box
- 9. Operational manual
- ◎ 10. Swing arm type of operation panel (only for DM-180 / DM-186)
- ◎ 11. Z-axis gear elevating reducer motor for knee up/down (only for DM-180 / DM-186)
- ◎ 12. XY-axes ball screw (only for DM-186)
| Model | DM-150V (no variable type) |
DM-160V DM-160VS |
DM-180V DM-180VS |
DM-186V DM-186VS |
|
|---|---|---|---|---|---|
| Spindle driving type | V | Pulley Step | |||
| VS | Inverter Variable | ||||
| Table | 1067 x 230 (42" x 9") |
1270 x 254 (50" x 10") |
1270 x 254 (50" x 10") |
1270 x 300 (50" x 12") |
|
| Capacity | X-axis travel (manual) | 730 | 850 (33.45") | 800 (31.5") | 860 (33.86") |
| X-axis travel (OP-power feed) | OP-700 | OP-750 (29.53") | OP-700 (27.56") | OP-840 (33.07") | |
| Y-axis travel | 310 (12.21") | 426 (16.77") | 426 (16.77") | 406 (15.98") | |
| Y-axis travel (OP-power feed) | OP-340 (13.39") | ||||
| Z-axis travel | 406 (15.98") | 446 (17.56") | 470 (18.5") | 420 (16.54") | |
| Z-axis travel (OP-gear type elevating reducer motor) |
OP-370 (14.57") | x | x | ||
| Quill travel | 127 (5") | 127 (5") | 140 (5.5") | ||
| XYZ axes travel will be shortened after DRO installed. | |||||
| Overarm travel | 457 (18") | 506 (22") | 540 (21.26") | ||
| Overarm swivel | 360° | ||||
| Spindle | Spindle taper - Vertical | NT-30 | NT-30 | NT-40 | |
| Spindle motor - Vertical | 2HP | 3HP (OP-5HP) | 3HP (OP-5HP) | 5HP | |
| Spindle speed 60HZ -V-step speed 50HZ |
80~2720 rpm 68~2280 rpm |
66~2700 rpm 68~2280 rpm |
70~3350 rpm 58~2780 rpm |
||
| Spindle speed 60HZ -VS-variable speed 50HZ |
x | Low: 60~460 rpm High: 460~3500 rpm |
Low: 55~450 rpm High: 445~3600 rpm |
||
| Vertical feed (Per revolution of spindle) |
0.04 / 0.08 / 0.15 mm/rev | ||||
| Measurement | Packing size | 1500 x 1640 x 2000 | |||
| N.W. / G.W. | 1000 / 1100 kgs | 1360 / 1460 kgs | 1600 / 1700 kgs | 1800 / 1900 kgs | |
| Standard color | RAL-7005 (gray) | ||||
| Model | A | B | C | D | E | F | G |
|---|---|---|---|---|---|---|---|
| Item | Height | Length (Depth) |
Width | Spindle nose to table surface | Head 45° inward | Head 90° (Spindle center to the column surface) |
Head 45° outwar |
| DM-150 V | 2010 | 1620 | 1468 | 0-430 | 0-285 | 171-482 | 228-533 |
| DM-160 V / VS | 2256 | 1900 | 1680 | 0-450 | 0-484 | 255-726 | 226-838 |
| DM-180 V / VS | 2300 | 1900 | 1680 | 0-450 | x | 166-700 | x |
| DM-186 V / VS | 2300 | 1900 | 1980 | 0-490 | x | 166-700 | x |
